How To Cover A Styrofoam Head With Fabric

How To Cover A Styrofoam Head With Fabric
How To Cover A Styrofoam Head With Fabric

How To Cover A Styrofoam Head With Fabric – DIY ornaments for Christmas or ornamental balls that may be used for other decorative purposes can be made by simply wrapping fabric around styrofoam balls. This method is both enjoyable and easy. Putting together these eye-catching fabric-covered balls requires only a few basic craft tools and a very short amount of time and how to cover a styrofoam head with fabric.

Table of Contents

How To Cover A Styrofoam Head With Fabric

This mybelizeblog.com create them on your own and give them as presents, or get your friends and family involved in a fun and creative afternoon activity by working on this project together.

How To Cover A Styrofoam Head With Fabric
How To Cover A Styrofoam Head With Fabric

Creating Different Zones Within the Ball

Utilizing a measuring tape that is flexible

Take the ball’s circumference measurement. A flexible measuring tape, such as the kind used by tailors, should be wrapped around the middle of the Styrofoam ball in a horizontal fashion. To get the circumference, just look at the number that appears on the end of the measuring tape where it connects to the beginning.

Draw eight even portions on the ball by connecting the poles with vertical lines.

You can determine how far apart to divide the sections of the ball by dividing the circumference of the ball by 8, which will give you the distance between each portion that you will be covering with a piece of cloth. Carefully mark eight vertical lines at even intervals, starting from the middle of the ball’s top and working your way down to the middle of the ball’s bottom.

Using a sharp knife, make cuts along the lines that are half an inch (1.3 cm) deep.

Make use of a craft knife or even a kitchen knife if it is very sharp. Place the blade of the knife in alignment with one of the drawn lines, then cut as precisely and straight as possible along that line. You will need to repeat this process for each of the designated lines in order to create the slits that the fabric pieces will be tucked into in order to keep them in place on the ball.

Developing a Design for the Fabric to Follow

Use a marker to draw two cut lines that are adjacent to each other from the ball onto a piece of paper.

Place a blank sheet of paper over the ball in such a way that it covers the two slits that are adjacent to one another. How to cover styrofoam with fabric to create the section outline for your pattern, carefully trace along the slits that are located on top of the paper.

Increase the width of the outline by approximately half an inch (1.3 centimeters) on both sides.

Place the piece of paper containing your outline on a surface that is completely flat. At a distance of approximately half an inch (1.3 centimeters) from the initial lines, draw parallel lines on both sides.

Utilizing scissors, I cut the outline out of the piece of paper.

You can use a pair of craft scissors or any other pair of household scissors that fits well in your hand and is easy for you to cut with. To remove your fabric pattern from the paper so that you may use it to cut out all of your gorgeous pieces of fabric, carefully cut along the second set of lines that you drew on the paper. This will allow you to use your pattern.

Preparing the Fabric by Cutting It Into Pieces

Attach your pattern to a scrap of fabric using pins.

When positioning your design over the portion of the fabric that you wish to use to adorn your ball, make sure to take into mind the pattern that is already present on the fabric. At each end of the pattern that has a point, carefully insert a pin through the paper and into the fabric.

Utilizing a pair of fabric scissors, cut the fabric all the way around the pattern.

Cut down one side of the pattern, going from point to point, using great care. Turn the fabric so that the cut edge is on the opposite side, then cut along that edge to create a piece of cloth large enough to cover one area of the ball.

To cut out the fabric for the rest of the parts, simply repeat the technique described above.

Attach the paper pattern to the other piece of fabric very carefully using pins. To obtain another strip of cloth, repeat the previous step of cutting around it with your fabric scissors. Continue doing this until you have a sufficient amount of fabric pieces to cover all of the different regions of the ball.

The process of putting together and embellishing the ball

Over the sections of Styrofoam, pin the pieces of fabric into place using the safety pins.

Place one piece of fabric over one area of the styrofoam ball, and then pull the fabric tightly in a vertical direction from the top pole to the bottom pole of the ball. At each of the poles, insert one pin through the fabric and into the Styrofoam. Repeat this process for each piece of fabric until the ball is completely encased in fabric.

Use the edge of a butter knife to tuck the excess cloth into the lines where it was cut.

Place the cutting edge of the knife over the part of the cloth that is positioned so that it is resting on top of one of the slits in the Styrofoam. Apply consistent pressure as you work your way down into the cut with the fabric. Repeat this process for the portion of the fabric that is located above each of the cut lines.

To conceal the raw edges of the tucked cloth, glue little pieces of chain or ribbon over the area.

Using scissors, snip off strands of cord or ribbon that are exactly the same length as the cut lines. On top of the tucked fabric, run a line of hot glue in the form of a thin bead along the length of one of the cut lines, and then press a piece of string or ribbon into the glue to secure it. This process must be repeated for each cut line.

If you wish to use the ball as an ornament.

You need first adhere a loop of ribbon to the top of the ball using glue. Make a loop with a length of Christmas ribbon and tie it off. Put a drop or two of hot glue in the exact middle of the top pole of the ball and let it cool. In order to secure the ribbon to the ball, you will need to press the knot of the looped ribbon into the hot glue.

As a nice finishing touch.

Glue a bow to the top of the ball that matches the ball’s color scheme. Make a bow out of a piece of decorative ribbon by tying it in a knot. Place the ornamental bow in the center of the top of the ball after squeezing a small amount of hot glue into the center of the top of the ball.

Put pearl-headed pins in the middle of the poles as a finishing touch for their beautiful appearance.

To give it a cleaner appearance, insert a pin with a pearl-headed tip into the exposed bottom pole. Repeat the same for the top pole, provided that it is not covered by a bow.

People Also Ask About How To Cover A Styrofoam Head With Fabric

Styrofoam Head Decorating Ideas
Styrofoam Head Decorating Ideas

How do you coat a styrofoam head?

Acrylic paint is highly recommended for use on styrofoam because of the excellent adhesion it has to the material. Because Styrofoam is so porous, how to make a styrofoam head look real it is highly likely that you will need to apply multiple coats of paint in order to cover it. When applying the paint, use a foam brush, and then wait for each coat to dry completely before applying further layers.

Can you cover Styrofoam with paper?

Paper should be used whenever there is a requirement to adhere something on Styrofoam. In addition to that, it works well with other materials that are frequently used in crafts, such as pieces of fabric and cardstock. It is sufficient to position the material atop the Styrofoam while ensuring that it uniformly covers the entire surface of the foam.

What can you coat Styrofoam with?

Liquid polyurethane can be used to create a durable coating for white EPS Styrofoam. Applying a coating with a firm surface will protect the Styrofoam props, cosplay clothes, and other projects you are working on. It is not necessary to use the nasty fiberglass resin in order to make your Styrofoam more durable. Simply use a liquid polyurethane hard-coat method that consists of two parts.

How do you cover a foam ball?

Place one piece of fabric over one area of the styrofoam ball, and then pull the fabric tightly in a vertical direction from the top pole to the bottom pole of the ball. At each of the poles, insert one pin through the fabric and into the Styrofoam. Repeat this process for each piece of fabric until the ball is completely encased in fabric.

Conclusion

How To Cover A Styrofoam Head With Fabric –┬áTape is utilized in residential vertical wall applications where FOAMULAR extruded polystyrene (XPS) board is utilized as continuous insulation over steel or wood wall frame. The purpose of this application is to tape the joints of the board. Foamular XPS insulation can be adhered to reliably with Owens Corning HomeSealR Foam Joint Tape.

Leave a Reply

Your email address will not be published. Required fields are marked *